Study on inhomogeneous cooling behavior of extruded profile with unequal and large thicknesses during quenching using thermo-mechanical coupling model

The interfacial heat transfer coefficient between hot profile surface and cooling water was determined by using inverse heat conduction model combined with end quenching experiment. Then, a Deform-3D thermo-mechanical coupling model for simulating the on-line water quenching of extruded profile with unequal and large thicknesses was developed. The temperature field, residual stress field and distortion of profile during quenching were investigated systematically. The results show that heat transfer coefficient increases as water flow rate increases. The peak heat transfer coefficient with higher water flow rates appears at lower interface temperatures. The temperature distribution across the cross-section of profile during quenching is severe nonuniform and the maximum temperature difference is 300 °C at quenching time of 3.49 s. The temperature difference through the thickness of different parts of profile first increases sharply to a maximum value, and then gradually decreases. The temperature gradient increases obviously with the increase of thickness of parts. After quenching, there exist large residual stresses on the inner side of joints of profile and the two ends of part with thickness of 10 mm. The profile presents a twisting-type distortion across the cross-section under non-uniform cooling and the maximum twisting angle during quenching is 2.78°.     

Synthesis of high-entropy diboride nanopowders via molten salt-mediated magnesiothermic reduction

Powder synthesis is critical for implementing the wide applications of high-entropy diborides (HEBs). However, the low-temperature synthesis of HEB powders was rarely reported. Herein, the low-temperature synthesis of the single-phase HEB nanopowders via molten salt-mediated magnesiothermic reduction (MMR) method was reported for the first time. The results showed that the as-synthesized nanopowders consisted of the single-phase HEBs and their average particle sizes are in the range of 28-56 nm. Meanwhile, they possessed the good compositional homogeneity and the low-content oxygen impurity in the range of 4.13-6.12 at%. In addition, their formation mechanism could be well interpreted by a classical MMR growth process.     

ZL109铝合金车削表面完整性实验研究

设计了三因素四水平正交车削实验,综合运用极差分析、方差分析等方法,研究了切削参数对硅铝合金ZL109车削表面完整性的影响规律,得到了切削参数对于表面粗糙度、残余应力和显微硬度的影响程度和趋势,分析了ZL109车削表面完整性的形成机理,以期为切削参数优选提供实验和理论基础。研究结果表明,进给量f对表面粗糙度具有显著影响,切削速度v和进给量f增加会导致表面残余拉应力增大,显微硬度受切削参数的影响较小。     

快速凝固高硅铝合金加热过程中的组织转变

利用气雾化法制备高硅铝合金粉末,采用光学显微镜(OM)、扫描电镜(SEM)等现代测试手段,分析快速凝固高硅铝合金不同粒度粉末微观组织和结构特征,研究在不同加热温度和保温时间条件下针状富铁相的转变特性及β-Si相的粗化行为。结果表明:快速凝固高硅铝合金组织主要以基体上分布有大量细小的颗粒状和针状相为特征,合金粉末在加热过程中,随着温度的升高和保温时间的延长,颗粒β-Si相有粗化趋势,针状非平衡富铁相转变为棒状或颗粒状平衡相。通过台阶式连续加热模拟试验可获得针状相基本消失且颗粒β-Si相未发生明显粗化的组织。     

扩散时间对W在TiAl合金中扩散行为的影响

通过光学显微镜、扫描电镜和硬度测试等分析手段研究了在1250 ℃下扩散保温不同时间对W元素在TiAl合金中扩散行为的影响。结果表明:试样在1250 ℃下进行扩散不同时间后,渗层界面处连接良好,可观察到明显的冶金结合。扩散层厚度随扩散时间的延长而增加,扩散4 h后可得到约15 μm厚的渗层,扩散24 h后可得到约45 μm厚的渗层,此外较长的扩散时间(24 h)可显著改善界面处的裂纹和气孔等缺陷。W在TiAl合金中的扩散机制主要为置换和空位扩散,且W和Ti的原子半径和热膨胀系数等存在差异,使得晶格畸变的出现并进一步阻碍了W元素的扩散。显微硬度试验结果表明W在TiAl合金中进行扩散,可以增强TiAl合金的硬度,且硬度值随W含量的增大而增大。     

自然时效效应及预时效处理对7A20铝合金组织性能的影响

研究了中强度7A20铝合金的自然时效硬化效应及预时效处理对组织和性能的影响。采用光学显微镜和透射电镜表征了其微观组织结构,采用维氏硬度计和万能拉伸试验机测试了其硬度和力学性能。结果表明:固溶态7A20试验铝合金的自然时效硬化效应明显,12天后硬度由56 HV0.5提高到122 HV0.5,提高了117.86%。经120 ℃×10 min预时效处理后,自然时效硬化增量最低,相比于固溶态降低了16 HV0.5,有效抑制自然时效硬化效应;同时,预时效处理提升了烘烤硬化效应,烘烤硬化后屈服强度提升了166 MPa,抗拉强度提高了51 MPa,伸长率降低了7%。烘烤处理前,其晶内的强化主要来自于与基体共格的GP区,烘烤处理后为尺寸小于5 nm、弥散分布的η′强化相。     

强变形工艺对2519A铝合金组织与性能的影响

通过硬度测试、拉伸性能测试、透射电镜观察等分析手段研究了不同强变形工艺下2519A铝合金的力学性能与微观组织。结果表明,经50%的冷轧变形和165 ℃人工时效后,2519A合金的力学性能明显提高,其抗拉强度、屈服强度和伸长率分别为522 MPa、468 MPa和8.5%。而在冷变形前添加165 ℃×2 h预时效处理,合金的力学性能进一步提高,其抗拉强度、屈服强度和伸长率分别达到535 MPa、497 MPa和8%。预时效处理可以提高合金中θ′相的密度,使析出相分布更加均匀,有助于提高合金的力学性能。     

喷射成形Al-Zn-Mg-Cu合金挤压态的组织和力学性能

研究了利用喷射成形辅以挤压制备Al-5.72Zn-2.36Mg-1.66Cu合金后优化的组织结构特征和力学性能。结果表明,合金基体组织均匀细化,晶粒形貌趋于圆整,平均晶粒大小达到10 μm左右。当合金的冷却条件通过快速凝固技术改变时,会产生不同程度的固溶强化效果和第二相弥散强化效果,从而改善了合金的整体性能。合金的屈服强度和抗拉强度分别平均提高了20%左右,且伸长率也略有提高。